Lampe de table globulaire en laiton

Un globulaire en laiton
lampe de table

Un globe arrondi en verre transparent repose dans un corps en laiton et en métal, fini en or ou noir. La forme industrielle et moderne se lit comme une petite sculpture sur une table. La lumière d'une ampoule LED ou Edison traverse l'abat-jour transparent et se propage vers l'extérieur dans la pièce

Du verre, du laiton et une lueur claire

Une lampe de table compacte en verre, laiton et métal, avec un choix d'or ou de noir

Verre et laiton

La lampe est faite de verre, de laiton et de métal, avec un globe arrondi comme forme principale

Or ou noir

Choisissez une finition dorée ou une finition noire

Teinte claire

L'abat-jour est transparent, donc l'ampoule reste visible et la lumière traverse le verre

LED ou Edison

Il faut une ampoule LED ou une ampoule Edison sur culot E27 ou E26, commutable par bouton poussoir et non dimmable

Taille et lumière

Hauteur	Diamètre 21 cm : 45 cm
Source lumineuse	Ampoule LED ou ampoule Edison
Base	E27 ou E26
Tension	CA 110-240 V
Couleur de l'ombre	Clair
Contrôle	Interrupteur à bouton-poussoir, non dimmable
Corde	Fil de 59″ (150 cm) avec fiche d’interrupteur ; peut être prolongé sur demande
Montage	Tableau
Environnement	Intérieur
Indice IP	IP20

Hauteur

Diamètre 21 cm : 45 cm

Source lumineuse

Ampoule LED ou ampoule Edison

Base

E27 ou E26

Tension

CA 110-240 V

Couleur de l'ombre

Clair

Contrôle

Interrupteur à bouton-poussoir, non dimmable

Corde

Fil de 59″ (150 cm) avec fiche d’interrupteur ; peut être prolongé sur demande

Montage

Tableau

Environnement

Intérieur

Indice IP

IP20

Choose how to install the light.

Tap a situation. The drawing marks the measurement, so you can see where to start.

76–91 cm

The line marks 76–91 cm from the bottom of the shade to the tabletop.

Dining table

Measure the table, not the room. Then check the light from every seat.

How to measure: Length and width of the top. For a round table, the diameter.
Starting size: Round: about half to two thirds of the width. Long: half to two thirds of the length.
Where to place it: Center the light over the table, even if the room center is elsewhere.
Clearance: Start with 76–91 cm from the shade bottom to the tabletop.

On a long table, two smaller pendants usually look better than one oversized light.

Before you drillTape a paper template to the ceiling and check it from the doorway and from a seat.

MeasureTop to shade bottom

Height76–91 cm

AlignCenter of the table

76–91 cm

The line marks 76–91 cm from the bottom of the shade to the island.

Kitchen island

Measure the usable island and keep the lights on its center line.

How to measure: Length and width of the working surface, not an unused overhang.
Starting size: One linear light: half to two thirds of the length. Several pendants: choose diameter first, then the count.
Where to place it: Even centers on the island’s center line.
Clearance: 76–91 cm above the counter. Leave the ends clear.

Mock the whole row, not a single pendant.

Before you drillThree paper circles show bad spacing before you drill.

MeasureCounter to shade bottom

Height76–91 cm

AlignEven centers

210 cm

The line marks 210 cm of clear walking room, from the lowest point to the floor.

Center of the room

Length plus width gives the starting diameter. Ceiling height decides whether it can hang.

How to measure: Length and width in centimetres.
Starting size: (Length + width in metres) × 8.3 ≈ diameter in cm. Example: 3.7 + 3.0 → about 56 cm.
Where to place it: Place it in the usable center of the room, not over a walking path.
Clearance: In the walkway, keep at least 210 cm under the lowest point.

An open form looks lighter. A dark, closed shade looks larger.

Before you drillCheck that the ceiling box can carry the weight before you drill.

MeasureL + W (m) × 8.3

Height210 cm walkway

AlignUseful center

210 cm

The line marks 210 cm of headroom. Space the lights 180–240 cm apart.

Hall and entry

A rhythm of small lights works better than one oversized piece in the middle.

How to measure: Clear length and width. Mark swinging doors and the start of the stairs.
Starting size: In a narrow hall, try a compact fitting about every 180–240 cm.
Where to place it: On the center line of the path.
Clearance: At least 210 cm under the lowest point. Do not block an open door.

A dimmer makes the same lights easier by day and by night.

Before you drillThe count comes from the spacing, not from one oversized diameter.

MeasureEvery 180–240 cm

Height210 cm walkway

AlignHall center line

165–178 cm8–15 cm8–15 cm

The line marks 165–178 cm from the floor to the center of the sconce. Leave 8–15 cm to the mirror.

Bathroom mirror

Light from the sides usually softens the face better than one light from above.

How to measure: Mirror width and height, and the wall space on each side.
Starting size: A pair of sconces: center at 165–178 cm from the floor. A bar over the mirror: about three quarters of its width.
Where to place it: Place the pair symmetrically. The nearest edge, 8–15 cm from the mirror.
Clearance: Check the frame, cabinet doors and tap. Choose a fitting rated for moisture.

If the sides are too tight, use a wide, diffused bar over the mirror.

Before you drillHold the sconce at the planned height and check the reflection before wiring.

Measure165–178 cm

Height8–15 cm to the mirror

AlignSymmetric pair

Shoulder

The dashed line runs through the seated shoulder: the bottom of the shade sits at that height.

Bedside

The seated position in bed matters, not the view from the door.

How to measure: Mattress height, and the height and width of the nightstand.
Starting size: Shade bottom near seated shoulder height.
Where to place it: Beside the bed, on the nightstand, with the light toward the book and not into the eyes.
Clearance: Keep the cord off the pillow. The switch should be reachable from bed.

Two different nightstands often need lights that adjust separately.

Before you drillTest it sitting up. What looks balanced from the door can glare at pillow height.

MeasureSeated shoulder

HeightSwitch in reach

AlignLight on the book

Eyes

The dashed line marks seated eye height. The shade sits above it, beside the shoulder.

Reading chair

Place the light beside or slightly behind the shoulder. Keep the brightest source out of view.

How to measure: Seat height and the distance to the planned lamp. Sit as you read.
Starting size: Floor lamp: shade bottom near seated eye height.
Where to place it: Beside or slightly behind the shoulder, never in front of the face.
Clearance: Keep the base out of the path. The bulb should not be visible at eye height.

Test with the other lights on and off. A dimmer helps at night.

Before you drillIf it still glares, lower the lamp, or choose a deeper shade or more diffusion.

MeasureSeated eyes

HeightOut of the path

AlignBeside or behind

Découvrez l'histoire de l'éclairage OME

Chez OME Lighting, nous pensons que l'éclairage est bien plus qu'une simple fonction : c'est un art qui métamorphose votre espace. Chaque pièce est conçue avec soin, animée par une passion pour le savoir-faire artisanal et une esthétique intemporelle. De nos finitions en laiton poli à la main à nos abat-jour en verre emblématiques, nous créons des pièces qui subliment chaque recoin de votre intérieur.

À propos de nous

Méthodes d'expédition	Livraison gratuite	Livraison rapide
Porter	Services médicaux d'urgence	UPS/DHL Express
Coût	Gratuit	114 $ la pièce
Temps de traitement	2 à 10 jours ouvrables	1 à 2 semaines
Délai de livraison	2 à 5 semaines	4 à 20 jours
Zone de livraison	À la plupart des pays	Disponible uniquement en Norvège, en Islande, à Chypre, au Liban et dans certaines régions des États-Unis, notamment à Porto Rico, en Alaska et à Hawaï.

Lampe de table globulaire en laiton